Estimate the amount of walking and determine the appropriate thickness specifications.

1. Check the equipment

Check all necessary equipment including Glue, Cuter, Ruler, Knife, Compass, Scriber, and Edge Cutter before construction.

2. Check Lot Number

Before dismantling the box, make sure that the tiles to be constructed are the same lot. If it is not the same lot, check that the color and surface emboss and gloss are the same.

3. Set Center Line and Start Point

Check the center line by drawing the horizontal and vertical centerline of the place to be constructed according to the drawing method. Mark the starting point so that the width of the product touching all walls is constant to ensure the overall balance of the room. For diagonal construction, adjust it to 45 degrees and adjust the starting point so that the part that contacts all the walls is in constant shape.

4. Check the precautions before applying the adhesive

Urethane glue and Epoxy are flammable and should not be approached during construction.

5. Apply Adhesive & Floor Attachment

Apply the adhesive thin and evenly with the prescribed application knife (0.8X1.6X2.0mm). Apply the tile after applying it for 20 to 30 minutes. The timing of construction varies slightly depending on the type of adhesive, room temperature and humidity. The wall is constructed at a distance of 2mm.

6. Finish the work

The adhesive on the tiled surface must be removed immediately before it hardens. Clean the acrylic adhesive with a clean cloth and, if it is a urethane adhesive, with alcohol.

1. Construction time

Floor construction should be done at the end after all other construction works(Paint, Wall paper, varnish) have been completed.

2. Check construction materials

Tile: Color, Size, Same Lot No, Sheen
Glue: Class, Maker, Requirement
Floor Patch: Class, Maker, Requirement

3. Installation site temperature

Tiles and adhesives should be kept at a constant temperature between 21 and 30 degrees Celsius from 28 hours prior to minimum application.

4. Floor moisture

The floor should be free of condensation or dampness when checked with a RMA Moisture Tester.

5. Indoor air circulation

The indoor air should be circulated so that a constant temperature from 21 "C to 37" C is evenly distributed from the floor to the ceiling, from the left corner to the right corner.

6. Construction

Construction equipment is managed by set of type. (Refer to DJ-TM-0279)

7. Construction Equipment

When the installation conditions do not align properly, it is necessary to make adjustments in consultation with the contracting parties. DJ-TM-0202, 0203, 0204 must be strictly adhered to.

You can keep tiles that are likely to be contaminated initially in a suitable way.

In particular, attention should be paid to asphalt marks, shoe polish, paint, rubber heel marks, rubber mat furniture footrests, kimchi soup, and smoking agent.

The following is a schematic of the sequence of decontamination of Decoria tiles.

You don't walk for a day until the tiles fit properly and you don't put furniture on the floor.

Do not clean the water for 3 days and then clean it with a dry duster to remove the water from the gaps. If the adhesive is hard on the surface, wipe it lightly with a nylon sponge.

When the floor is completely clean, a small amount of wax is soaked in the floor or clean linen, and evenly applied in the direction and spacing.
* Be Careful not to step on the applied floor.

Wait until completely dry after application. The drying time depends on the product, so check in advance.

The floor is scratched and scratched by dirt or fine sand, so cleaning is done regularly.

When the liquid is spilled, wipe off the neutral detergent with a clean cloth.Wipe out grease with an alkaline detergent.

Spray cleaning of coated tiles with 3M red pad and uncoated tiles with 3M blue pad is recommended.

Tile floors coated for walk can be polished with a leather pad.

emove dust, fine sand, and other signs adhering to the floor.

Dilute a water-based cleaner with 5 to 8 times water. Wet a cloth with dilution and wipe the floor. Do not use rough pads, strong abrasive cleaner or wire brushes.

Scrape marks that do not disappear with a cleaner should be lightly rubbed off with a kitchen pan oil scrubbing pad.

When removing the coated wax, apply a suitable amount of wax remover to the floor and return it to the barf.Baffin operation must be handled by trained personnel at the appropriate RPM.

At the end of the blast, collect the water with a sponge scraper before the floor is dry and then use a vacuum cleaner to wash it.

Wipe it off with a clean mop again, dry it, and then apply wax coating about 2 to 3 times.

The cause of pollution

• Floors polished with furniture polish, glass cleaner, and silicon polish
• a damp spot
• Pollution, Small sand
• Floor grease

Solution

• Wipe out silicone polish with alkali detergent.
• Wipe out the water with a duster and dry it. Remove the entrance mat and dry it.
• Clean the mat at the entrance regularly.
• If the layer of wax is oily, clean it with alkali detergent or wax remover.

The cause of pollution

• Use improper cleaning pad
• dust or sand
• Not often or too much buffing

Solution

• Do not use black or brown pads
• Clean the dust thoroughly before installing the membrane at the entrance.
• They do regular cleaning at places away from their main walking sites.

The cause of pollution

• In case of waxed area not cleaned
• Carpet or matte with rubber soles Contact with the tyre in the showroom, etc

Solution

• Remove the wax, clean it, and apply new wax.
• Install a separate protection panel to the area and use non-recording material.

The cause of pollution

• The concentration of the cleaner doesn't match.
• Insufficient wax coating, The re-coating cycle is too long.
• Barping pad unsuitable
• Use dirty cleaning equipment

Solution

• Check the concentration of the cleaning fluid container.
• Remove the wax coating and return to clean.
• Check the pad specifications.
• Remove the wax with clean equipment and coat again.

The cause of pollution

• Insufficient buffing
• Use a dirty rag
• Contamination by fine sand, Dust at the entrance
• an inadequate concentration of cleaner
• The dirty condition of the floor itself
• Less removed wax remover

Solution

• Use a less polished pad attached to the buffer.
• Before you mop, first clean the broom.
• Place a mat on the side of the entrance.
• Use a clean pad.
• Clean the floor.
• Remove the wax, clean it completely, and c oat it again.

The cause of pollution

• Re-coating before waxing is dry.
• If the coating does not mix well with the first application.
• The buffing pad or brush is too rough or does not fit properly.

Solution

• Make sure the first coating is dry before applying it again.
• Peel off, wipe and coat again.
• Follow maintenance standards.

1. Store the product in a flat, even surface.
(Exercise caution when working with the product in an upright position to avoid potential toppling.)

2. When moving the product to a higher location, use appropriate lifting equipment to avoid the risk of falling accidents.
(Wear a safety helmet and assign a dedicated person to operate outdoor lifts or similar equipment.)

3. 본 제품은 무거운 제품이므로 2인 이상이 호흡을 맞추어 운반해 주십시오.

4. 불에 직접 닿거나 불 옆에 놓으면 변형이 되거나 연화하는 일이 있습니다.

5. 전열 기구 및 스팀기 사용 시 변형, 변색 등의 원인이 될 수 있으니 사용에 주의하시기 바랍니다.

6. 본 제품 위에 물기 또는 미끄러운 물질이 있으면 미끄럼 사고가 발생할 수 있으니 주의하시기 바랍니다.

7. 제품은 바닥 시공용 제품이므로 이외의 용도로는 사용할 수 없습니다.

1. Please install this product by separating and using the same lot.
(Failure to separate lots may result in defects.)

2. Please thoroughly remove any foreign substances from the floor before installation. (Foreign substances include dust, paint, etc.)

3. We are not responsible for any product damage caused by foreign substances (such as dust, paint, etc.).

4. The actual product color may vary from the color in the sample book.

5. The line on the back of the product is a cutting guide line, and when cutting, please take precise measurements to avoid any loss.

※ Please store the rolls in an upright position.